NICE GATE AUTOMATION · UAE

NICE ROA81 M6 Steel Sliding Gate Rack 30×30×1000 mm UAE

Product Code: ROA81 Brand: NICE Origin: Italy
NICE automation products UAE delivery inquiries Installation guidance
Product Price

Contact us for price

Need installation or compatibility advice?Ask about gate size, motor selection, remote compatibility and UAE delivery.
Contact our team

NICE ROA81 M6 Steel Sliding Gate Rack 30×30×1000 mm UAE

ROA81 Sliding Gate Rack: Product Overview

NICE ROA81 is a galvanised steel Module 6 rack measuring 30 × 30 × 1000 mm. NICE specifies this weld-on rack for use with the RUA12 M6 crown/pinion in compatible installations. It is intended for projects that require this particular drive arrangement, including suitably designed commercial or industrial entrances.

Features Explained

Specified tooth module: M6 identifies the rack profile that must mesh with the motor pinion. Check this before comparing price, section size or mounting method. Correct tooth engagement is essential for transmitting movement smoothly along the gate travel.

One-metre sections: Sections can be arranged along the required travel. Measure the complete working run and the end positions before ordering. The opening width alone may not equal the finished rack length, so use the installer’s layout to establish quantity.

Construction and profile: M6 identifies the gear module, not a six-millimetre rack thickness. The 30 × 30 mm section describes the physical rack profile. Both details matter when identifying a replacement: a dimensional match without a matching tooth module is not a compatible part.

Technical Specifications

ManufacturerNICE
Part numberROA81
Gear moduleM6
Dimensions30 × 30 × 1000 mm
Section length1000 mm / 1 metre
MaterialGalvanised steel
MountingWeld-on
Selection limitCompatible M6 drive; NICE specifies RUA12 pinion

Choosing the Correct Rack

Select ROA81 only for a compatible M6 drive arrangement. It cannot replace an M4 ROA6, ROA7 or ROA8 rack simply because each is supplied in one-metre lengths. Verify the RUA12 pinion requirement and the exact motor configuration. A thicker rack does not independently establish a permissible gate weight.

For a replacement, photograph the existing rack, motor identification plate and mounting points. Include a ruler in a clear side-view image so the profile can be checked. A damaged short section may also indicate a problem with the adjacent sections or pinion, so inspect the whole engagement path before fitting a new part.

Mounting and Alignment

This is a weld-on rack. The gate structure, working height and drive alignment must be planned before permanent fixing. Heavy gate installations require particular attention to support rollers, stops and the stability of the motor foundation; the rack should not become a substitute support rail.

Begin with a gate that moves freely on its own supports. Check the full travel for binding, wheel wear and track obstructions. Use the motor manual’s clearance requirement between rack and pinion: the gate must not rest on the drive gear. Keeping the rack straight is as important as selecting the correct model.

At each joint, preserve the tooth spacing and height. A small step between sections can become a repeated knock each time it crosses the pinion. After fixing, move the gate through its complete travel and inspect the joint transitions before powered commissioning. Recheck the fasteners or welds after the initial operating test.

Kit Includes and Ordering Quantity

One 1 m ROA81 galvanised steel rack section. The RUA12 pinion is a separate accessory and is not included unless expressly stated in your quotation.

The listing describes an individual one-metre section. State the number of sections required in your enquiry and confirm the quotation’s unit quantity. Catalogue factory packing quantities should not be assumed to be the amount supplied for one ordered item.

Applications

Use this rack in a compatible new sliding entrance or a properly assessed replacement project. Villa entrances, warehouse access and commercial premises have different gate masses and operating patterns. Confirm both the motor’s suitability and the rack arrangement for the actual site rather than choosing from the property type alone.

Maintenance in UAE Installations

During servicing, inspect tooth condition, mounting security and alignment. Remove debris from the travel area and investigate new grinding or repeated clicking sounds promptly. Outdoor sand and gate movement can reveal marginal installation tolerances; do not increase motor force to overcome a mechanical fault.

For steel sections, examine exposed or worked surfaces for corrosion and protect them as appropriate to the installation. Follow the manufacturer’s maintenance instructions for the rack and drive. Avoid applying an unapproved lubricant that can attract abrasive contamination to the working teeth.

Why Choose NICE ROA81?

This model provides a clearly identified rack specification for matching a NICE-compatible drive arrangement. Ordering by part number, module and dimensions makes replacement planning more reliable than ordering a generic “one-metre rack” without checking the installed system.

Supply and Installation Enquiries UAE

Contact NICE Gate Opener UAE with the motor model, gate dimensions, estimated gate weight, rack photographs and installation emirate. Ask for supply-only pricing or a quotation covering rack replacement, alignment and commissioning. Enquiries can cover Dubai, Sharjah, Abu Dhabi and other UAE locations.

Frequently Asked Questions

How long is one ROA81 section?
The specified section length is 1000 mm, equivalent to one metre.

Which tooth module does it use?
ROA81 uses M6. The motor pinion must match this module.

Can I combine M4 and M6 sections?
No. Different modules have different tooth geometry and must not be mixed along the same drive run.

Will changing the rack increase my motor capacity?
No. The complete installation remains limited by the drive, gate mechanics and all applicable component specifications.

Can a new section fix a noisy gate?
Only if the damaged rack is the cause. Check alignment, supports, joints and the pinion before replacing parts.

What should I send for a replacement enquiry?
Send the part number if available, profile measurements, motor model and photographs of the mounting arrangement.

Why Choose Us?

Discuss the rack specification and the installation requirements in one enquiry. Clear product identification and a defined supply scope help avoid ordering a section that does not suit the existing tooth profile or mounting geometry.