NICE ROA6 M4 Nylon Sliding Gate Rack 1 Meter UAE
NICE ROA6 M4 Nylon Sliding Gate Rack 1 Meter UAE
ROA6 Sliding Gate Rack: Product Overview
NICE ROA6 is a reinforced nylon rack for compatible sliding gates weighing up to 500 kg. Its metal insert reinforces the section while the nylon teeth engage the drive pinion. It is a useful option for a residential entrance where a suitable M4 rack and controlled, relatively quiet engagement are priorities.
Features Explained
Specified tooth module: M4 identifies the rack profile that must mesh with the motor pinion. Check this before comparing price, section size or mounting method. Correct tooth engagement is essential for transmitting movement smoothly along the gate travel.
One-metre sections: Sections can be arranged along the required travel. Measure the complete working run and the end positions before ordering. The opening width alone may not equal the finished rack length, so use the installer’s layout to establish quantity.
Construction and profile: The nylon body and metal reinforcement perform different roles: the tooth surface provides the engagement interface while the insert supports the structure. Correct mounting remains necessary; reinforcement does not compensate for loose screws or a distorted gate.
Technical Specifications
| Manufacturer | NICE |
|---|---|
| Part number | ROA6 |
| Gear module | M4 |
| Dimensions | 25 × 20 × 1000 mm |
| Section length | 1000 mm / 1 metre |
| Material | Nylon with internal metal insert |
| Mounting | Slotted fixing design |
| Selection limit | Gate weight up to 500 kg; compatible M4 drive required |
Choosing the Correct Rack
Choose ROA6 when the actual gate mass is within its 500 kg limit and the motor uses a suitable M4 pinion. Installing it alongside a motor rated for a heavier gate does not increase the rack’s limit. For heavier installations, compare an appropriately rated rack before ordering.
For a replacement, photograph the existing rack, motor identification plate and mounting points. Include a ruler in a clear side-view image so the profile can be checked. A damaged short section may also indicate a problem with the adjacent sections or pinion, so inspect the whole engagement path before fitting a new part.
Mounting and Alignment
Slotted mounting points allow the installer to set the section against a straight datum. The attachment method must suit the gate frame. A nylon section should not be treated as a weld-on steel rack, and mounting pressure should not deform its tooth line.
Begin with a gate that moves freely on its own supports. Check the full travel for binding, wheel wear and track obstructions. Use the motor manual’s clearance requirement between rack and pinion: the gate must not rest on the drive gear. Keeping the rack straight is as important as selecting the correct model.
At each joint, preserve the tooth spacing and height. A small step between sections can become a repeated knock each time it crosses the pinion. After fixing, move the gate through its complete travel and inspect the joint transitions before powered commissioning. Recheck the fasteners or welds after the initial operating test.
Kit Includes and Ordering Quantity
One 1 m ROA6 rack section. Confirm the fixing hardware required for your gate frame when ordering.
The listing describes an individual one-metre section. State the number of sections required in your enquiry and confirm the quotation’s unit quantity. Catalogue factory packing quantities should not be assumed to be the amount supplied for one ordered item.
Applications
Use this rack in a compatible new sliding entrance or a properly assessed replacement project. Villa entrances, warehouse access and commercial premises have different gate masses and operating patterns. Confirm both the motor’s suitability and the rack arrangement for the actual site rather than choosing from the property type alone.
Maintenance in UAE Installations
During servicing, inspect tooth condition, mounting security and alignment. Remove debris from the travel area and investigate new grinding or repeated clicking sounds promptly. Outdoor sand and gate movement can reveal marginal installation tolerances; do not increase motor force to overcome a mechanical fault.
For steel sections, examine exposed or worked surfaces for corrosion and protect them as appropriate to the installation. Follow the manufacturer’s maintenance instructions for the rack and drive. Avoid applying an unapproved lubricant that can attract abrasive contamination to the working teeth.
Why Choose NICE ROA6?
This model provides a clearly identified rack specification for matching a NICE-compatible drive arrangement. Ordering by part number, module and dimensions makes replacement planning more reliable than ordering a generic “one-metre rack” without checking the installed system.
Supply and Installation Enquiries UAE
Contact NICE Gate Opener UAE with the motor model, gate dimensions, estimated gate weight, rack photographs and installation emirate. Ask for supply-only pricing or a quotation covering rack replacement, alignment and commissioning. Enquiries can cover Dubai, Sharjah, Abu Dhabi and other UAE locations.
Frequently Asked Questions
How long is one ROA6 section?
The specified section length is 1000 mm, equivalent to one metre.
Which tooth module does it use?
ROA6 uses M4. The motor pinion must match this module.
Can I combine M4 and M6 sections?
No. Different modules have different tooth geometry and must not be mixed along the same drive run.
Will changing the rack increase my motor capacity?
No. The complete installation remains limited by the drive, gate mechanics and all applicable component specifications.
Can a new section fix a noisy gate?
Only if the damaged rack is the cause. Check alignment, supports, joints and the pinion before replacing parts.
What should I send for a replacement enquiry?
Send the part number if available, profile measurements, motor model and photographs of the mounting arrangement.
Why Choose Us?
Discuss the rack specification and the installation requirements in one enquiry. Clear product identification and a defined supply scope help avoid ordering a section that does not suit the existing tooth profile or mounting geometry.
