NICE GATE AUTOMATION · UAE

NICE ROA8 M4 Steel Sliding Gate Rack 30×8×1000 mm UAE

Product Code: ROA8 Brand: NICE Origin: Italy
NICE automation products UAE delivery inquiries Installation guidance
Product Price

Contact us for price

Need installation or compatibility advice?Ask about gate size, motor selection, remote compatibility and UAE delivery.
Contact our team

NICE ROA8 M4 Steel Sliding Gate Rack 30×8×1000 mm UAE

ROA8 Sliding Gate Rack: Product Overview

NICE ROA8 is a galvanised steel M4 gear rack supplied with screws and spacers. Its 30 × 8 mm profile is intended for compatible sliding gate drives where a steel rack with spacer mounting is appropriate. A one-metre section can be used in a new installation or as part of a carefully matched repair.

Features Explained

Specified tooth module: M4 identifies the rack profile that must mesh with the motor pinion. Check this before comparing price, section size or mounting method. Correct tooth engagement is essential for transmitting movement smoothly along the gate travel.

One-metre sections: Sections can be arranged along the required travel. Measure the complete working run and the end positions before ordering. The opening width alone may not equal the finished rack length, so use the installer’s layout to establish quantity.

Construction and profile: Spacer mounting separates the tooth-bearing section from its attachment points. That can make alignment and later servicing practical, but only if the spacers are positioned accurately and the fasteners remain secure. A loose mounting point can produce noise even when the teeth themselves are undamaged.

Technical Specifications

ManufacturerNICE
Part numberROA8
Gear moduleM4
Dimensions30 × 8 × 1000 mm
Section length1000 mm / 1 metre
MaterialGalvanised steel
MountingScrews and spacers
Selection limitCompatible M4 drive and suitable gate structure

Choosing the Correct Rack

Choose ROA8 when you need the 30 × 8 mm steel profile and a suitable spacer-and-screw attachment. ROA7 is also M4 but uses a different section and installation arrangement. Matching the tooth module alone does not guarantee an existing mounting line will accept a different rack.

For a replacement, photograph the existing rack, motor identification plate and mounting points. Include a ruler in a clear side-view image so the profile can be checked. A damaged short section may also indicate a problem with the adjacent sections or pinion, so inspect the whole engagement path before fitting a new part.

Mounting and Alignment

The spacers establish the mounting offset and the rack is secured with screws. This arrangement should be laid out so every section follows the same pinion line. Allow access to the fasteners for adjustment and future servicing rather than burying them behind additional gate cladding.

Begin with a gate that moves freely on its own supports. Check the full travel for binding, wheel wear and track obstructions. Use the motor manual’s clearance requirement between rack and pinion: the gate must not rest on the drive gear. Keeping the rack straight is as important as selecting the correct model.

At each joint, preserve the tooth spacing and height. A small step between sections can become a repeated knock each time it crosses the pinion. After fixing, move the gate through its complete travel and inspect the joint transitions before powered commissioning. Recheck the fasteners or welds after the initial operating test.

Kit Includes and Ordering Quantity

One 1 m ROA8 galvanised steel rack section with screws and spacers. Motor, foundation hardware and gate fabrication are separate.

The listing describes an individual one-metre section. State the number of sections required in your enquiry and confirm the quotation’s unit quantity. Catalogue factory packing quantities should not be assumed to be the amount supplied for one ordered item.

Applications

Use this rack in a compatible new sliding entrance or a properly assessed replacement project. Villa entrances, warehouse access and commercial premises have different gate masses and operating patterns. Confirm both the motor’s suitability and the rack arrangement for the actual site rather than choosing from the property type alone.

Maintenance in UAE Installations

During servicing, inspect tooth condition, mounting security and alignment. Remove debris from the travel area and investigate new grinding or repeated clicking sounds promptly. Outdoor sand and gate movement can reveal marginal installation tolerances; do not increase motor force to overcome a mechanical fault.

For steel sections, examine exposed or worked surfaces for corrosion and protect them as appropriate to the installation. Follow the manufacturer’s maintenance instructions for the rack and drive. Avoid applying an unapproved lubricant that can attract abrasive contamination to the working teeth.

Why Choose NICE ROA8?

This model provides a clearly identified rack specification for matching a NICE-compatible drive arrangement. Ordering by part number, module and dimensions makes replacement planning more reliable than ordering a generic “one-metre rack” without checking the installed system.

Supply and Installation Enquiries UAE

Contact NICE Gate Opener UAE with the motor model, gate dimensions, estimated gate weight, rack photographs and installation emirate. Ask for supply-only pricing or a quotation covering rack replacement, alignment and commissioning. Enquiries can cover Dubai, Sharjah, Abu Dhabi and other UAE locations.

Frequently Asked Questions

How long is one ROA8 section?
The specified section length is 1000 mm, equivalent to one metre.

Which tooth module does it use?
ROA8 uses M4. The motor pinion must match this module.

Can I combine M4 and M6 sections?
No. Different modules have different tooth geometry and must not be mixed along the same drive run.

Will changing the rack increase my motor capacity?
No. The complete installation remains limited by the drive, gate mechanics and all applicable component specifications.

Can a new section fix a noisy gate?
Only if the damaged rack is the cause. Check alignment, supports, joints and the pinion before replacing parts.

What should I send for a replacement enquiry?
Send the part number if available, profile measurements, motor model and photographs of the mounting arrangement.

Why Choose Us?

Discuss the rack specification and the installation requirements in one enquiry. Clear product identification and a defined supply scope help avoid ordering a section that does not suit the existing tooth profile or mounting geometry.